EV charger installation guide
Wall mounting, electrical connection and Bemis Charge Hub app setup for Bemis wall-mounted AC chargers; step by step with animations, based on the installation and user manuals.
- Wall mounting in 8 steps
- 4 app connection flows
- 10 manuals & documents
Wall charger installation
Charger Plus 2 and Charger Pro 2 are wired externally: the supply cable goes under the rear terminal cover, the housing stays closed and the unit hangs on the wall bracket. Charger 2 is also wired at a covered rear terminal block.
For indoor and outdoor use. Choose a flat wall away from direct sun, heat sources, flammable vapours and chemicals.
- Plus 2 IP66 · IK10 · Pro 2 IP65 · IK08
- -25 … +55 °C · RH 5–95%
- Indoor/outdoor
Connecting to the Bemis Charge Hub app
The app is available on the App Store and Google Play as Bemis Charge Hub. Add the charger to your account to start charging from your phone, monitor it remotely over Wi-Fi, use it via Bluetooth without internet and register RFID cards. RFID cards are used on wall-mounted units.
App and device setup · 6 stepsConnecting to the Bemis Charge Hub appDownload the Bemis Charge Hub app from the App Store or Google Play.
Using a portable charger
Pro Mobile 2, Mini Mobile and Mono Mobile need no installation: plug into a suitable socket and run the cable to the car. What the lights and display mean, choosing the level and safe use: step by step with animations, based on the user manual.
Pro Mobile 2 plugs into a red three-phase CEE socket: 5×16 A or 5×32 A by model. If none is available, use a home socket with the supplied adapter.
- 5×16 A · 5×32 A CEE plug
- Adapter cable 30 cm
- IP65 · IK08
Installation and user manuals
The product manuals as PDFs. Click a cover to open it in your browser or download it.
AC chargers
Wall-mounted: Charger 2 · Plus 2 · Pro 2
DC charging cable
CCS2 DC charging socket and cable
Related documents
Extra documents for before and after installation
Technical requirements
Values from the installation and user manuals
- Supply cable (22 kW)
- 5×6 mm² up to 50 m, 5×10 mm² from 50 to 100 m; additional board beyond 100 m
- Protection
- 40 A type B circuit breaker and 40 A, 30 mA Type A RCD (no more than 1 m from the unit)
- Mounting height
- Lowest point of the unit 0.8 m to 1.5 m above the floor; not to be mounted on a ceiling or sloping wall
- Earthing
- Earth resistance below 100 Ω, earth–neutral voltage below 1 V
- Cable end
- Strip 10 mm and fit ferrules; earth conductor same cross-section as phase
- Cable route
- In conduit, flexible conduit or cable tray; under roads, a covered concrete duct at least 40 cm deep
Portable chargers
Pro Mobile 2 · Mini Mobile · Mono Mobile
Related documents
Extra documents for before and after installation
Technical requirements
Values from the installation and user manuals
- Mini Mobile
- 2.3 / 3.7 kW · 1×16 A earthed plug, 200–250 V
- Mono Mobile
- 3.7 / 7.4 kW · 2P+E 32 A CEE plug, 200–250 V single-phase
- Pro Mobile 2 (7/11 kW)
- 5×16 A CEE plug, 380–415 V three-phase
- Pro Mobile 2 (11/22 kW)
- 5×32 A CEE plug, 380–415 V three-phase
- Vehicle connection
- Type 2 connector, Mode 2; 5 m cable, 8 and 10 m options
- Adapter
- To use a home socket when no suitable socket is available; 30 cm cable; Mono Mobile adapter on level 1 only (3.7 kW)
- Protection, conditions
- Mini and Mono IP66 · IK10, Pro Mobile 2 IP65 · IK08; operating temperature -30 … +55 °C
Common questions
Choose the right home charger
Use the charger finder to identify the right Bemis charger for your car and electrical installation in a few questions, or browse the wall-mounted models.